Skip to content
View in the app

A better way to browse. Learn more.

Large Scale Modeller

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

1:32nd scale RAF RE.8

Featured Replies

Hi all,

As the Sopwith 2F.1 Camel is coming to a close, I've started researching the next build.

The Wingnut Wings RAF RE.8 kit.

I'll model this as a RE.8 of the 6me Escadrille, Belgian Aviation Militaire, at Houthem-lez-Furnes airfield in 1917.

This particular aircraft, serial number A 3715 ‘6’, was built in Coventry, England and was transferred to Belgian’s in July 1917.

Initially this aircraft was delivered with the RAF 4a engine fitted, but this was later replaced by a Hispano-Suiza engine.

It will be modelled as initially powered by the standard 150-horsepower RAF 4a V-12 engine, when it was first operated by 6me Escadrille in 1917.

This aircraft was shot down in 1918 when crewed by pilot Adj. Simonet and observer Lt. Piron.

I have the Pheon decal set for the RE.8 which has the Belgian markings.

However, the Pheon colour profiles have the aircraft colour as very dark, almost black.

However, other profiles of the same squadron show the colour to be closer to the RFC PC 10 or 12 finish.

Mike

colourscheme.jpg

Edited by sandbaggeruk

  • Author

Hi all,
I've been preparing the fuselage internals and cockpit parts.
Fuselage halves wood effect painted with Tamiya Dark Yellow (XF60).
Then Windsor & Newton Griffin Alkyd Raw Sienna oil paint.
MRP Clear Doped Linen MRP-256 used for linen.
Alclad Duraluminium ALC102 used for metal panel area.
Flory Dark Dirt wash used to dirty up the surfaces.
Cockpit parts wood effect as before.
Tamiya acrylics used for painting all other detail. 
AK Interactive Kerosene wash AK2039 used for fuel stains.
Clear UV resin used for instrument faces glass.

The pilots wicker seat is molded solid, so that will be replaced with a Barracuda Studios rean seat.

Now it's onto cleaning up for assembly and rigging the bracing wires and control cables,

Mike

pit1.JPG

pit2.JPG

pit3.JPG

pit4.JPG

  • Author

Hi all,

The basic RAF 4a engine is complete.

There is more to add, including some weathering, but not until its fitted into the fuselage.

The only modifications were:

Thinning the walls of the cylinder cover plates.

Adding 0.2 mm diameter lead wire as ignition leads to each spark plug.

Mike

eng1.JPG

eng2.JPG

  • Author

Hi all,

The basic cockpit is completed.

It still needs the pilots seat and lap straps and the observers seat.

Also the bracing wires and control cables.

When test fitting the cockpit between the fuselage halves, I found I needed to remove material.

This was from the fuel tank and fuselage mating surfaces and from the edges of the fuselage opening.

Now its onto adding the rigging and seats,

Mike

pit5.JPG

pit6.JPG

testfit.JPG

  • Author

Hi all,

A few more additions to the cockpit before the seat are fitted.

I've rigged only those wires and cables that will be seen.

Twin rudder cables, tailplane incidence cables and crossed side bracing wires.

As the cockpit structure is long, using mono-filament may cause distortion when tensioned.

Therefore I chose to use EZ fine line, as that has more give.

0.2 mm diameter lead wire was used for the gun trigger cable and morse key cables.

The throttle rod is 0.3 mm diameter Nickel-Silver rod,

Mike

pitrigged.JPG

morsecables.JPG

throtrod.JPG

trigcable.JPG

interesting as i just sold a WNW Wingnut Wings RE.8 and Halberstadt CL.II Duelists pair on ebay at the end of last month

  • Author

Hi all,

Both seats are now fitted.

Now time to close up the fuselage,

Mike

seatsin.JPG

I admire how you have the patience to paint all the small details, even though most of them remain hidden.🥇

  • Author

Hi all,

Just a small addition.

A map on the observers map shelf.

The map was a Tommy's War paper map secured with PVA adhesive,

Mike

map.JPG

Nice touch. the wicker seat is interesting. The texture on the leather. Oil paints?

  • Author
On 9/11/2026 at 4:08 PM, Moon Puppy said:

Nice touch. the wicker seat is interesting. The texture on the leather. Oil paints?

he wicker seat is a 3D printed replacement from Barracuda Studios.

Yes, both the pilots seat cushion and observers seat were stippled oil paints - Windsor and Newton Raw Umber and Raw Sienna oil paints.

Mike

  • Author

Hi all,

The fuselage has now been closed up.

The top, front locating peg and barrel inside the cover panel for the engine cylinders is large and obvious.

Therefore, after assembly, I cut away the peg and barrel,

Mike

fusjoin.JPG

pancurve.JPG

  • Author

Hi all,

A few updates to the build.

Lewis and Vickers machine guns.

Hale 100lb and Cooper 20lb bombs.

Interplane, cabane and aileron struts.

Mike

cooper.JPG

hale.JPG

lewis.JPG

vickers2.JPG

struts.JPG

  • Author

Hi all,

Basic paintwork done.

AK Interactive grey primer (AK758).

Underside surface rib tapes MRP Dark Wood (MRP-262) with Tamiya Deck Tan (XF55) top coats.

Upper surfaces MRP Khaki Green (MRP-333).

Nose panels were painted metal, so colour is darker than on linen - black base coat.

Fuel tank - mix of Tamiya NATO Brown (XF80) with Red (X7) to a ratio of approximately 60/40%.

White areas MRP Bianco White (MRP-308).

Next is to paint any detail,

Mike

paint1.JPG

paint2.JPG

paint3.JPG

paint4.JPG

  • Author

Hi all,

Decals have been applied.

A mix of the kit decals and the Pheon RE.8 decal set.

The fin serial number had to be created from numbers from two separate kit decals.

The rudder had number 1 but the aircraft modelled had number 6.

I cut out the yellow with number band from the Pheon decals.

The rudder was painted yellow and the remaining red and black decal section were applied.

The number 6 was from a Xtradecal set, as were the fuselage white stripes and the fuel tank restraining straps.

I modified the kit Aldis gun sight to represent that fitted to this aircraft.

I also scratched the mounted generator for the wireless set.

Next up is to represent the bungee type cords to the side arms of the Lewis gun mounting.

Then it'll be onto weathering and pre-rigging before assembly,

Mike

decals3.JPG

decals4.JPG

bits.JPG

Edited by sandbaggeruk

  • Author

Hi all,

Slight weathering applied.

This was a combination of:

Flory Models Dark Dirt clay wash

Flory Models Grime clay wash

AK Interactive Kerosene wash

AK Interactive Engine oil wash

Tamiya Weathering Master Set A (Mud)

Tamiya Weathering Master Set D (Oil Stain.

Now it's onto fitting fuselage components before pre-rigging,

Mike

weather1.JPG

weather2.JPG

weather3.JPG

weather4.JPG

weather5.JPG

  • Author

Hi all,

The Vickers machine gun has been fitted with its Constantinesco interrupter gear.

Also the Scarf mounting for the Lews machine gun.

Now it's onto pre-rigging before assembly,

Mike

vickerson.JPG

scarfon.JPG

  • Author

Hi all,

Pre-rigging done.

Before the upper wing is fitted I've pre-rigged as much as possible to make final rigging access less restricted.

Inner flying wire pairs.

Intermediate flying wire pairs.

Outer flying wire pairs.

Interplane strut incidence wires.

Landing wires.

Landing gear bracing wires.

Cabane strut bracing wires (side and front).

Fin double bracing wires.

Rudder control cables.

Elevator control cables.

Aileron control cables.

Next up is to fit the upper wing,

Mike

beforewingon.JPG

  • Author

Hi all,

The upper wing is now fitted.

Next up is the fun part - final rigging,

Mike

wingon.JPG

  • Author

Hi all,

First of the final rigging done.

Fuselage cabane side bracing wires.

Fuselage twin front bracing wires.

Drag wires.

All 0.12 mm diameter monofilament with blackened 0.5 mm diameter Brass tube,

Mike

frig1.JPG

frig2.JPG

frig3.JPG

  • Author

Hi all,

A bit more of the rigging done.

Inner pairs of flying wires.

Intermediate pairs of flying wires.

Landing wires.

Interplane strut incidence wires.

Double fin bracing wires.

I have two more structural wires and the outer pairs of flying wires to fit then it's onto the rudder, aileron, elevator and tail skid control cables,

Mike

frig4.jpg

frig5.jpg

frig6.jpg

frig7.jpg

frig8.jpg

frig9.jpg

frig10.JPG

frig11.JPG

Edited by sandbaggeruk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.
Background Picker
Customize Layout

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.