October 3Oct 3 Hi all,As the Wingnut Wings RE.8 model is nearing completion, I'm researching the next model.I think six years of waiting for the Copper State kit to be released was enough.Therefore, I've decided to build the Lukgraph 3D printed version instead.Hansa-Brandenburg D.I, Serial No: 28.15 of Flik 41/J at Sesana, 4th August 1917.This particular aircraft was built by the Phönix company as one of a batch 28.01 – 28.24 ordered on the 24th of June 1916.It was powered by the Austro-Daimler 185hp 6-cylinder water-cooled in-line piston engine, 138 kW (185 hp).The aircraft was delivered to Flik 41/J on the 2nd of March 1917.On the 24th of April 1917, Chief pilot Feldpilot Oblt. Leo Bisce was injured when he crashed while landing at the Sesana airfield.After being repaired by Flep 1 at Marburg, the aircraft was returned ti Flik 41/J.On the 4th of August it again crashed at Sesana during a test flight when being flown by the Austro-Hungarian ace Linke-Crawford.It was sent to Flep 9 for repair but was too badly damaged and was written off on the 11th of September 1917.Mike Edited Sunday at 08:24 PM5 days by sandbaggeruk
October 12Oct 12 Author Hi all,Initial start on the build.Wing support rod exit holes in wing tips filled with UV setting resin then sanded.Upper wing ailerons pinned and angled.Elevators pinned and angled.Rudder pinned.The support rod holes through the two lower wings were blocked with resin and cannot be totally drilled out.I've asked Lukgraph if replacement wings can be sent.Otherwise the lower wings will not be fully supported and may sag or distort.The pilots seat as supplied is solid and seems too long and narrow.The actual seat also had lightening holes in the seat frame, which was covered with basic padding with cushion.I chose to replace the seat with one from Gaspatch.Although not the correct seat for this aircraft, it is of a correct size at least.The instrument panel does not seem to be configured the same as the actual instrument panel.However, this may be the result of service modifications carried out.As supplied the engine throttle lever is on the right side of the cockpit.The actual aircraft seems to have the throttle lever on the left side of the cockpit.Mike Edited October 19Oct 19 by sandbaggeruk
October 19Oct 19 Author Hi all,The fuselage is closed up now.I've just added a few bits.Throttle control rod.Rudder control cables.Elevator control cables.Aileron control tubes.Gun trigger cable.Replacement seat.Now it's onto external pre-rigging, which is only the landing gear bracing wires and rudder control cables,Mike
October 22Oct 22 Author Hi all,The basic fuselage is complete now.Tamiya Dark Yellow (XF60) base coated then Windsor and Newton Raw Sienna oil painted.Weathering is Flory Models Dark Dirt wash, Tamiya Weathering Master Set A (Mud) and Set D (Oil Stain).Mike
October 23Oct 23 Author Hi all,I ordered 80 and 100 mm long 1.2 mm diameter drills to clear the resin blockages in the lower wing support holes.The 80 mm long drills arrived today and easily drilled out most of the blockages.Once the 100 mm long drills arrive and are used the support holes will be clear to fully insert the support rods giving adequate wing support.Another potential problem is the length of the kit supplied support rods. For best support of the wings the kit supplied 1.2 mm diameter steel rods ought to be long enough to span from one wing tip to the other.However, they are not long enough for the upper and lower wings.If the rods were long enough (wing tip to wing tip) they would be able to support the entire upper wing assembly without any flexing strain on the upper wing halves at the wing centre section.The same applies for the lower wings at the fuselage.One option would be using the kit supplied rods inserted into the wings but with only short ends protruding to insert into the holes in the upper wing centre section and fuselage for the lower wings.Given the brittle nature of the 3D printed material I think the weight of the wings could put strain on those joints and with possible alignment errors.A second option would be to insert the rods through the upper wing centre section and fuselage for the lower wings with equal rod protrusion at each side.But that means the rods would not be far enough into the wings for full wing support.Therefore, I've ordered 300 mm lengths of 1.2 mm steel rod which will span wing tip to wing tip.Using these rods means there would be no joint strain at the upper wing centre section and fuselage for the lower wings.Also the wings will be fully supported,Mike
October 31Oct 31 Author Hi all,Further progress on the kit.I used the 100 mm long 1.2 mm diameter drills I ordered to clear resin blockage from inside the support rod holes through the lower wings.This now allows the 300 mm long 1.2 mm steel rods I ordered to fit through the lower wings and the fuselage, giving adequate support across the model.The same applied to the upper wing and its centre section.All flight surfaces are fished apart from detail painting and weathering.Base coated with Khaki Green 3/G3 (MRP-333) then the internal structure masked off.A coat of MRP Clear Doped Linen (MRP-256) was airbrushed over then the masking removed.Spare Iron Cross markings were applied to the underside of the upper wing to represent the see-through marking from above.Finally an MRP Clear Doped Linen (MRP-256) coat was airbrushed to fade and blend the structure to the surrounding areas.Aviattic unbleached Clear Doped Linen (CDL) clear backed (ATT32254) decal was applied to cover all flight surfaces.The Lukgraph decals were as usual extremely fragile and were breaking up when just sliding them off their backing sheet.This is the seventh of their models I've built and the decals were the same on all of them.I managed to assemble the decals and painted any fine crack or split seams.The six tailplane support struts in the kit are supplied as three pairs, each pair being of different lengths.The kit instructions show the struts located but give no indication as to which struts fit where on the model.I found that the following applies:The longest pair of struts are fitted above the tailplanes.The shortest pair of struts are fitted as the underside rear struts.The remaining pair of struts are fitted as the underside forward struts.The kit supplied figure is not bad but the body length appears too long and there's not a great deal of surface detail.Rather than modify the figure, I've chosen to use a figure from Copper State Models instead.I've started test assembling the unique interplane struts and already I've had issues, which I'll detail later,Mike Edited October 31Oct 31 by sandbaggeruk
Sunday at 08:24 PM5 days Author Hi all,It happens !!Accidently dropped the model.Wings, fuselage and landing gear smashed.Not much left of the rest either.Hey-Ho - moving on,Mike
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.